How to Stop Holiday Light Fuses From Blowing
Last Updated: November 1, 2026
Quick Summary
Holiday lights blow fuses because too much electrical load runs through a circuit that can’t handle it, or because of damaged strands or loose, water-exposed connections. Start by unplugging everything and inspecting each strand, plug and wire for damage. Then plug strands in one at a time to find the faulty one, and keep total load under the circuit’s rating.
- Unplug everything and check each strand, plug and wire for damage first.
- Discard any strand that flickers, buzzes, feels warm or smells like burning.
- Plug strands in one at a time until the fuse blows to find the culprit.
- Add up wattage on the same circuit and stay well under its rated capacity.
- Replace a blown plug fuse only with one matching the printed amperage rating.
Table of Contents
Holiday lights blow fuses for a simple reason: too much electrical load is running through a circuit that can’t handle it. This problem is almost always preventable. A fuse or breaker exists to cut power before wires overheat, so a blown fuse is a warning, not a random failure.

The most common causes are overloaded circuits, damaged light strands, and loose or water-exposed connections. Each one pushes more current through wiring than it was built to carry, or creates a weak spot where heat and sparks can build. Once you understand which cause you’re dealing with, the fix becomes much clearer.
Many homeowners assume a bad fuse is the problem. Sometimes it is, but more often the fuse is doing its job by protecting the circuit from something else. Replacing it again and again without finding the cause just invites a bigger problem.
Here is the good news. You can usually track down the cause in an afternoon by working through a few simple checks, in order. The steps below walk through that process, from inspecting your lights to deciding when it’s time to call a professional.
Holiday light safety guidance from the U.S. Consumer Product Safety Commission (cpsc.gov) and the National Fire Protection Association (nfpa.org) covers many of the basics below. CPSC holiday decorating safety tips NFPA holiday decorating fire safety
Step 1: Check Every Strand, Plug and Wire for Damage
Start with the lights themselves before you touch the fuse. Unplug everything first. Then look closely at each strand, plug, and wire for damage.
Frayed insulation, cracked sockets, and stretched or twisted wires all create hazards in holiday lights. Check where the cord meets the plug, since that spot takes the most stress over a season.
- Look for cracked or melted plastic on plugs and sockets, and learn how to prevent outdoor light corrosion at connections that can cause faults.
- Feel for warm spots along the cord while it’s connected
- Replace any strand with exposed copper or bare wire (CPSC Urges Consumers to Decorate Safely for the Holidays)
- Discard strands that flicker, buzz, or smell like burning
Watch out: a strand that feels warm or smells faintly of burning is a fire risk, not just a nuisance. Pull it from service before you test anything else.
Step 2: Find the Strand Causing the Blown Fuse
If the lights look fine, the next step is to isolate the problem. Plug in strands one at a time until the fuse blows again. The last strand you connected is your suspect.
This method takes patience, but it works. Once you find the faulty strand, remove it and test the rest of the display. A repeat blowout with the same strand confirms the diagnosis.
How Many Christmas Lights Can You Plug Into One Outlet?
The honest answer depends on the type of lights and the circuit. Incandescent bulbs draw far more current than LEDs, so the same outlet can handle a much larger LED display. Always follow the connection limit printed on each light set’s packaging or manual.
Limits vary by product and circuit, so use the manufacturer’s limit as your starting point. Use the manufacturer’s limit as your starting point, and never exceed it.
- Check the wattage printed on each strand’s label
- Add up the total wattage on the same circuit
- Keep total load well under the circuit’s rated capacity
- Use a separate circuit for large animated displays when possible
How to Replace a Blown Holiday Light Fuse Safely
Some light sets have a small replaceable fuse built into the plug. If yours does, always match the replacement fuse to the rating printed on the plug or in the manual. Installing a higher-amp fuse removes the protection the fuse was meant to provide.
Unplug the set before opening the fuse compartment. Use a fuse of the exact same amperage and size. Never use foil, wire, or a coin as a substitute, since that can start a fire.
Why GFCI Outlets Trip With Christmas Lights
A GFCI outlet cuts power when it detects current leaking to ground, which can happen with moisture or damaged insulation. Outdoor outlets are GFCI-protected for good reason. If your outlet trips repeatedly, the cause is usually a damp connection or a cord with a worn spot.
Dry all plugs and connections, then reset the outlet. If it trips again, unplug everything and test strands individually to find the faulty one.
When to Stop Troubleshooting and Call an Electrician
Stop and call a licensed electrician if the breaker trips again after you’ve removed every suspect strand, if you see scorch marks on an outlet or panel, or if the outlet feels hot. These signs point to a wiring problem, not a light problem.
Don’t keep testing circuits that smell of burning or show damage. Professional help is faster and safer than guessing.
Set Up Your Display to Run Safely Next Season
Prevention beats repair. Store lights carefully, keep connections dry and elevated, and use outdoor-rated extension cords outside. Plan your circuits before you hang anything, and spread large displays across multiple outlets.
Keep a log of which strands and outlets you used. That record makes next season’s setup faster and helps you spot problems early. Browse our animated holiday light displays on The Holiday Light Store website for current options and pricing.
Frequently Asked Questions
Why do the fuses in my holiday lights keep blowing?
Repeated blown fuses usually mean too much current is flowing through one strand or circuit, or there is damage somewhere in the wiring. Incandescent strands draw far more current than LED strands, so a set that worked fine with LEDs may overload a plug fuse when swapped out. Damaged sockets, frayed cords, and moisture inside a plug are other common causes. Unplug everything, check each strand, and reconnect them one at a time to find the faulty one.

How many holiday light strings can I safely connect together?
Follow the connection limit printed on the light manufacturer’s packaging or instructions first, since that number is the most reliable guide. Limits vary by product, so follow the manufacturer’s stated connection limit. Use an electrical load calculation with the wattage on each label to confirm you stay under the circuit’s 15-amp or 20-amp rating, and never daisy-chain beyond the stated limit.
Can I replace a blown holiday light fuse with a higher-amp fuse?
No. A fuse is a safety device sized to the wire and the strand it protects. Installing a higher-amp fuse lets the wire overheat before the fuse blows, which can start a fire. Replace a blown fuse only with one of the exact same amperage and voltage rating printed on the plug or the original fuse. If the replacement fuse blows right away, stop and find the cause rather than changing the rating.
When should I call an electrician about a holiday display that keeps tripping a breaker?
Call a licensed electrician if a circuit breaker trips repeatedly after you have removed the faulty strand, if you see scorched outlets, smell burning, or notice warm plugs or receptacles, or if the outlet itself feels loose. Those signs point to a wiring or circuit problem that a homeowner should not troubleshoot further. Electricians can also confirm whether your outdoor circuits have the right capacity for a large display.
